POWER ELECTRONICS FOR LINEAR AND ROTARY SOLENOIDS

 

We offer some ready-to-use power electronic circuits for the control of linear solenoids and rotary solenoids:

 

Pick&Hold: these provide a higher current - and thus an increased force - for a defined time when switching on, which is then reduced to the holding value; this makes it possible to compensate for the often unfavorable characteristic force curve of solenoids and to achieve a higher starting force and at the same time reduce the average power and thus the thermal load on the actuator; pick & hold amplifiers can thus enable the use of smaller and also more cost-effective actuators under certain circumstances; when selecting windings, low-resistance windings are used so that the desired coil current or the desired force can be achieved in every situation, even with warm solenoids and the associated higher coil resistance; this is another advantage of pick & hold circuits - as the force is dependent on the current, it is reproducible by the current control and is not subject to the fluctuations caused by the thermal changes in the resistance if only a fixed voltage is applied. The peak time, the peak current and the holding current can be set using software (free of charge, USB-C connection).

Pick&Drop: these are driven with a short pulse that provides the voltage for the adjustable time and then switches back to 0V.

PWM (analog): this is the analog control variant; by means of an analog voltage or current input the output voltage can be varied proportionally.

Cyclic on/off: this circuit variant enables the voltage to be switched on/off cyclically; the frequency, the duty cycle and the voltage can be influenced.

Position control: this is a simple controller circuit with PID control for a limited stroke or angle with analog feedback or encoder feedback.

Geeplus dual channel driver for two linear and rotary solenoids or bipolar solenoids, intelligent and programmable Pick-and-Hold-circuit, 12V, 24V, 48V, USB-C, software included
Geeplus Pick and Hold driver for linear and rotary solenoids, programmable, 24V, 48V, 60V, single chanel
OES drive circuits for solenoids: Pick and Hold, Pick and Drop, Proportional, Closed Loop
type model voltage
Vdc
continuous
current
Adc
peak
current
Adc
channels input
signal
adjustment feedback size
circuit board
mm
information
Pick & Hold PHu-50 8 - 50 0.1 - 25 0.1 - 25 2
bipolar or
2 single channel
pulse
5 - 24 Vdc
peak time
peak current
continuous current
(RS-232)
- 55 x 39 x 29 manual
Software PHu 6.1 (zip)
Pick & Hold PHu-150 16 - 75 0.1 - 24 0.1 - 24 1 pulse
3 - 30 Vdc
peak time
peak current
continuous current
(RS-232)
- 80 x 42 x 32 manual
Pick & Hold PH-ET-xx 9 - 50 4 15 1 - 2 pulse
3Vdc up to
supply voltage
peak time
continuous voltage
(with 2 potentionmeters
on board)
- 76.2 x 76.2 x 21.5 data sheet
wiring diagram
Pick & Drop PDD-01 9 - 50 4 15 1 pulse
3Vdc up to
supply voltage
on time
(with potentiometers
on board)
- 76.2 x 76.2 x 21.5 data sheet
wiring diagram
Proportional PWM-xx 9 - 50 4 15 1 - 2 analog
voltage 0 - 5Vdc
current 4 - 20mA
max. voltage
(with potentiometers
on board)
- 76.2 x 76.2 x 21.5 data sheet
wiring diagram
Cyclic on/off LOC-01 9 - 50 4 15 1 pulse
3Vdc up to
supply voltage
frequency
output voltage
on time
(with 3 potentiometers
on board)
- 76.2 x 76.2 x 21.5 data sheet
wiring diagram